Amazon Best Sellers

How To Clean An Indoor Bath And Shower With A Power Washer?

How To Clean An Indoor Bath And Shower With A Power Washer?

Cleaning an Indoor Bath and Shower With a Power Washer is the process of removing dirt, mold, mildew, or other contaminants from surfaces that can be reached by water. Cleaning these areas with a power washer provides better sanitation. In addition, it removes stains and rust caused by mineral deposits in hard water.

It’s essential to have access to hot water when cleaning an indoor bath and Shower with a power washer. Because this will help loosen any built-up debris on the walls or floor before being washed away. 

Cleaning your home’s bathroom should be done regularly for personal hygiene. It will prevent potential health risks such as mold-related allergies, asthma attacks, chronic sinusitis, and respiratory problems.

What You’ll Need

  • A fan-tipped electric pressure washer
  • Sponge
  • Microfiber mop
  • Toothbrush/grout pen
  • Elbow grease

How To Clean An Indoor Bath And Shower With A Power Washer: 5 Easy Steps

1. Remove the entire Shower. Everything, in its entirety! Shower goods, shavers, toys for the kids, soaps, and other items. Pressure washers use a strong stream of water to fracture and eject any loose objects. It may be dangerous, so make sure you clear everything out.

2. Make sure the extractor fan is on. Power washers deliver a fine spray that may cause moisture and dampness in the bathroom.

3. 3, 2, 1… Let’s go! Spray the entire surface of your shower tub enclosure with the pressure washer. First, use a 45-degree fan tip to sweep away any light dust from the whole space. 

Later, you may focus on problem areas with a narrow 15-degree fan tip. Because it could remove any loose grout fragments, this is something you want to save for last.

4. Add all the things taken out of the shower enclosure back into their original space (shower goods, shavers, toys for the kids, soaps). Next, clean your tubs and tiled surfaces with a sponge attached to your power washer’s wand. 

Then scrub hard, stubborn areas with a stiff-bristled brush. Finally, Work on grout lines with a toothbrush or grout pen after the Shower is finished.

5. Spray soapy water onto surfaces for improved cleaning results without potentially scratching or damaging your existing tub, tile, or fixtures. Cleaning an Indoor Bath and Shower With a Power Washer requires various cleaning products as well as a pressure washer.

 Clean your Shower regularly, and you can prevent future mold buildup and mildew odors caused by an overgrowth of water-loving bacteria.

Recommended Pressure Washer 

Last update on 2022-01-14 / Affiliate links / Images from Amazon Product Advertising API

Getting Rid of Dirty Grout Lines

To get rid of dirty grout lines, choose the right cleaning product. For example, cleaning an indoor bathroom and Shower With a Power Washer requires an acid cleaner because it’s strong enough to dissolve mineral deposits without gently harming your porcelain surfaces.

Clean tile with grout using hydrochloric or muriatic acid and water. The cleaner must sit on the grout for a minimum of 10 minutes, and you cannot rinse it off after this time has passed because it will damage your tile surface.

Precautions and Safety Considerations

Can a pressurized power washer clean a shower or bathtub enclosure in a matter of minutes? The answer is yes, but some cautions need to be followed. 

Cleaning with a power washer can provide fast results. Still, it can also cause damage if done incorrectly or without proper safety equipment.

It would be best if you first considered conditions and cautions:

– Cleaning with a power washer is best done by two people, not just one.

– The water supply must be sufficient to provide the pressure desired for cleaning. If you need more pressure, turn the pressure up on your house before starting. It’s recommended that an outdoor faucet be shut off while cleaning is done.

– Cleaning a bath or Shower inside a house is best done with a telescoping wand so the power washer will stay directed at the surfaces being cleaned. Cleaning an indoor bath and Shower with a power washer can be hazardous if not done correctly. So cleaning should only be done by people experienced with using a pressure washer.

– The area should be well ventilated and any plants in the immediate vicinity removed. The power washer makes a lot of suds, and they can turn into soap bubbles that may block your nose and eyes when you least expect it.

– Cleaning with a pressure washer is not recommended for bathtubs or shower stalls with semicircular fiberglass or acrylic panels. Cleaning the corners of these enclosures is best done with a microfiber mop and some elbow grease.

– Cleaning with a power washer is not recommended for walls and floors of bath and shower areas that have been painted within the past year, unless you want to strip the paint. Cleaning an indoor bath and Shower with a power washer can remove paint if applied at the wrong pressure or for too long.

– Cleaning with a pressure washer is recommended for tiles, fiberglass, marble, ceramic tile, brick, and other surfaces that do not require annual repainting to keep them looking good.

– Do not power-wash ceramic or porcelain tile floors. This method is only suitable for bathtub shower walls.


Never use a gas-powered pressure washer indoors. When running, gasoline engines emit deadly carbon monoxide gas that must be constantly ventilated.

Final Verdict on How To Clean An Indoor Bath And Shower With A Power Washer

Cleaning an indoor bath and Shower with a power washer is possible, but it’s best left to those that have used one before. Power washers are not appropriate for all flooring surfaces, and misusing one can result in harm or damage. 

It is not suggested for individuals who have no prior experience utilizing a power washer.

Happy cleaning!

Share on facebook
Share on twitter
Share on pinterest
Share on email
Share on print
Brett Tyler

Brett Tyler

I’m Brett Tyler, an entrepreneur, but more importantly (well, to me at least), a tool head. I’m passionate about all sorts of machines and how they work – it’s in my blood.

Leave a Comment

Your email address will not be published.